Ham Radio
Ham Radio, Electronics, Software and more...

Home » Ham Radio Mods » Icom Mods » ICOM R7000 Display Issue / R7000 Sensitivity Problem (ICOM R7000 Display Issue / R7000 Sensitivity Problem)
ICOM R7000 Display Issue / R7000 Sensitivity Problem [message #3004] Mon, 02 September 2013 13:29
root is currently offline  root
Messages: 207
Registered: December 2004
Senior Member
If you are having trouble with you Icom R7000 display being flaky
and then a sudden decrease in sensitivity try the following:


PROBLEM: ICOM R7000 radios that are used 24 hours a day for a long time
(2 years ) when shut off the display will become flaky and it
is also possible for a lost in overall gain (3 to 40 db).

SOLUTIONS: Officially there is ICOM ECO SB# 9288-004, attached below.

Unofficially from Tech who repairs R7000
The ECO does help the display problem, but most likely
it is not the problem. *

* note repairing your own radio my void you warranty and only
allow a qualified technician to do the job, otherwise damage
could happen to your R7000. If the VCO does not track then a
major alignment would have to be done after. Check the
ICOM IC-R7000 Service Manual for more details before starting
this repair, and to make sure I have not made any typing errors
you should get a copy of the ECO from ICOM !

1st SOLUTION:
Replace on the DC to DC Board the following capacitor.
Check the noise with an oscilloscope on both sides of
R3, if the noise is not way down on one side then
replace C2 a 33uf 16V capacitor. Noise feedback
can decrease the overall sensitivity of the R7000.

Replace on the Display Board
C19 and C20 a 10 uf 16VDC capacitor

I found that on my R7000 C19 & C20 were the cause of my
display problems. They are 10 uf electrolytic capacitors
that are lemon yellow pc mounted units, when they go bad
the base of the yellow caps change to a brown color.

I put in the following ECO first but it did not help. If
you look at the service manual you will see that the ECO
values are on the schematic but my unit had the old values.
I suggest that you check the above first, it is a lot easier
to do, C19/C20 can be done in 10-15 min while the ECO will
take about a hour.


2nd SOLUTION: The ECO


ICOM America, INc
2380-116th Ave, N.E.
Bellevue, Washington 98004
206-454-7619


SERVICE BULLETIN


UNIT MODEL R7000
SB# 9288-004
EFFECTIVE DATE 4/1/88
SERIAL # AFFECTED: ALL
PRODUCT GROUP: Amateur

BACKGROUND INFORMATION:
Display failure do to weak components

TECHNICAL INFORMATION:
Improvement in DC to DC converter and display power supply.

PARTS AFFECTED BOARD TYPE CHANGE TO NEW PART NUMBER
Q1/Q2 2SC 1214 DC to DC Board 2SC 2655 906-00385
R1/R2 3.3 KOHM DC to DC Board 5.16 K 915-01173
C3/C4 PF DC to DC Board 0.001 MF 50V 918-01500
ceramic cap
Q11/Q12 Display Board 2SC2655 906-00385
R31/R32 3.3KOHM Display 5.16k Ohm 915-01173
C13/C16 Display 0.001 MF 918-01500

DETAIL PROCEDURE:

1. Remove top and bottom cover.
2. Remove front panel sub-assembly from main chassis of radio
3. Remove the DC to DC board and replace components as listed
4. Reinstall DC to DC board.
5. Replace front panel sub-assembly onto main chassis of radio
6. Replace top and bottom covers.

ESTIMATE TIME TO COMPLETE IS 1 hour

Previous Topic: ICOM IC-R7000 Repair - Capacitors
Next Topic: Icom IC-706mkiig IF-SDR
Goto Forum:
  


Current Time: Sat Nov 25 00:42:01 EST 2017

Total time taken to generate the page: 0.03561 seconds